Asus AAM6020BI-T4 User Manual Page 1

AAM6030BI CPE User Manual AAM6030BI User Manual Rev. 1.00 Version date: Oct. 20, 2004

AAM6030BI User Manual 8. If prompted, click on to restart your computer with the new settings. 9. After restarting your PC, double-click on the Ne

AAM6030BI User Manual 3.2.5 Windows NT 4.0: 1. In the Windows NT task bar, click on the Start button, point to Settings, and then click Control Pane

AAM6030BI User Manual 4. Setting up your CPE This section will guide you through your CPE’s configuration. The CPE is shipped with a standard defau

AAM6030BI User Manual Figure 2 (Home page) 4.3 Setup To setup your CPE with a basic configuration, from the Home page, select Setup. Figure 3 illu

AAM6030BI User Manual 4.3.1 Wide Area Network connection On the other side of the router is where your Wide Area Network (WAN) connection; also refer

AAM6030BI User Manual and VCI settings; your DSL service provider or your ISP will supply these; in this case the DSL service provider is using 0,35.

AAM6030BI User Manual c. On-Demand: Enables on-demand mode. The connection will disconnect if no activity is detected after the specified idle timeou

AAM6030BI User Manual service provider is using 0,30. Also select the quality of service (QOS); leave the default value if you are unsure or the ISP

AAM6030BI User Manual 4.4.1.4 DHCP Connection Setup Dynamic Host Configuration Protocol (DHCP) allows the CPE to automatically obtain the IP address

AAM6030BI User Manual name; the name must not have spaces and cannot begin with numbers. In this case the unique name is called STATIC1. Select the

AAM6030BI User Manual Table of Contents 1. Introduction 4 1.1 Features & System Requirements 4 2. Your CPE at a glance 5 2.1 Ports and buttons

AAM6030BI User Manual 4.5 Configuring the LAN By default, your CPE has DHCP server (LAN side) enabled. If you already have a DHCP server running on

AAM6030BI User Manual Figure 10 (Example of a DHCP Relay configuration) By turning off the DHCP server and relay the network administrator must caref

AAM6030BI User Manual Figure 11 (Management IP address) The apply button will temporarily save this connection. To make the change permanent you nee

AAM6030BI User Manual 4.6.1 UPnP UPnP NAT and Firewall Traversal allow traffic to pass-thru the router for applications using the UPnP protocol. Thi

AAM6030BI User Manual The apply button will temporarily save this connection. To make the change permanent you need to click on Tools (at the top of t

AAM6030BI User Manual Figure 13 (Port Forwarding & Netmeeting) The apply button will temporarily save this connection. To make the change perm

AAM6030BI User Manual Figure 14 (IP QoS) IP Filters This firewall feature allows you to block network access based on a user's computer IP addr

AAM6030BI User Manual or deny) is performed. The user should note that the bridge filter will only examined frames from interfaces which are part of t

AAM6030BI User Manual 4.6.7 Multicast/IGMP Snooping Multicasting is a form of limited broadcast. UDP is used to send datagrams to all hosts that belo

AAM6030BI User Manual Figure 16-2 (IGMP SNOOPING) 4.6.8 Static Routing If the CPE is connected to more than one network, you may need to set up a st

AAM6030BI User Manual 4.7.1 System Commands 32 4.7.2 Remote Log 32 4.7.3 User Management 32 4.7.4 Update Gateway 33 4.7.5 Ping Test 33 4.7.6 Mod

AAM6030BI User Manual Figure 17 (Static Routing) The apply button will temporarily save this connection. To make the change permanent you need to cli

AAM6030BI User Manual Figure 18 (Dynamic Routing) The apply button will temporarily save this connection. To make the change permanent you need to c

AAM6030BI User Manual 4.7 Tools The CPE supports a host of tools which will allow you to customize and debug your CPE. 4.7.1 System Commands To mak

AAM6030BI User Manual The apply button will temporarily save this connection. To make the change permanent you need to click on Tools (at the top of

AAM6030BI User Manual Figure 20 (Ping test) 4.7.6 Modem Test The Modem Test is used to check whether your Modem is properly connected to the WAN Ne

AAM6030BI User Manual 4.8.6 System Log You can display the CPE’s log by going to the Home screen, under the Status title, click System log. From

AAM6030BI User Manual 5. Appendix A: Troubleshooting Below is a list of commonly asked questions. Before calling technical support, please look thro

AAM6030BI User Manual 5.4 The DSL Link LED continues to blink but does not go solid 1. This means that the DSL line is trying to train but for some

AAM6030BI User Manual 6. Router terms What is a firewall? A firewall is protection between the Internet and your local network. It acts similarly to

AAM6030BI User Manual 1. Introduction Congratulations on becoming the owner of a AAM6030BI CPE (Customer Premises Equipment). Your LAN (Local Area Ne

AAM6030BI User Manual 2. Your CPE at a glance Your CPE has many ports, switches and LEDs. Let’s take a look at the different options. Depending upo

AAM6030BI User Manual z Parts List In addition to this document, your AAM6030BI should come with the following: f AAM6030BI ADSL 4 Port Router f Po

AAM6030BI User Manual 3. Getting Start This chapter provides basic instructions for connecting the CPE to a computer or a LAN and to the Internet vi

AAM6030BI User Manual 3.2 Configuring Your PC Before you start to access the CPE via Ethernet, you must configure your PC’s TCP/IP address to be 192.

AAM6030BI User Manual The Local Area Connection Properties dialog box is displayed with a list of currently installed network components. If the list