Asus P5GD1 User Manual Page 45

  • Download
  • Add to my manuals
  • Print
  • Page
    / 128
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 44
ASUS P5GD1ASUS P5GD1
ASUS P5GD1ASUS P5GD1
ASUS P5GD1
2-252-25
2-252-25
2-25
4.4.
4.4.
4.
Serial ATA connectorsSerial ATA connectors
Serial ATA connectorsSerial ATA connectors
Serial ATA connectors
(7-pin SATA1, SATA2, SATA3, SATA4)(7-pin SATA1, SATA2, SATA3, SATA4)
(7-pin SATA1, SATA2, SATA3, SATA4)(7-pin SATA1, SATA2, SATA3, SATA4)
(7-pin SATA1, SATA2, SATA3, SATA4)
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
If you installed Serial ATA hard disk drives, you can can create a RAID
0 or RAID 1 configuration with the Intel
®
Matrix Storage Technology
through the onboard Intel
®
ICH6R RAID controller. Refer to Chapter 5
for information on creating a RAID configuration.
Important notes on Serial ATAImportant notes on Serial ATA
Important notes on Serial ATAImportant notes on Serial ATA
Important notes on Serial ATA
These connectors support the Intel
®
Matrix Storage Technology.
The Serial ATA RAID feature (RAID 0, RAID 1) is available only if you
are using Windows
®
2000/XP.
Install the Windows
®
2000 Service Pack 4 or the Windows
®
XP
Service Pack1 before using Serial ATA.
Use only a maximum of 2 ports for each RAID 0 or RAID 1 set.
Plug your Serial ATA boot disk on the master port (SATA1 and
SATA2) to support S3 function. Refer to the table below for details.
Serial ATA Master/Slave connectorsSerial ATA Master/Slave connectors
Serial ATA Master/Slave connectorsSerial ATA Master/Slave connectors
Serial ATA Master/Slave connectors
P5GD1
P5GD1 SATA connectors
SATA1
SATA4
SATA3
SATA2
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXP1
RSATA_RXN1
GND
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXP2
RSATA_RXN2
GND
GND
RSATA_TXP4
RSATA_TXN4
GND
RSATA_RXP4
RSATA_RXN4
GND
GND
RSATA_TXP3
RSATA_TXN3
GND
RSATA_RXP3
RSATA_RXN3
GND
These connectors are set to Standard IDE configuration by default. In
Standard IDE mode, you can connect Serial ATA boot/data hard disk
drives to these connectors. If you intend to create a Serial ATA RAID set
using these connectors, set the
Configure SATA AsConfigure SATA As
Configure SATA AsConfigure SATA As
Configure SATA As item in the BIOS
to RAID. See section “4.3.6 IDE Configuration” for details.
ConnectorConnector
ConnectorConnector
Connector
SettingSetting
SettingSetting
Setting
UseUse
UseUse
Use
SATA1, SATA2 Master Boot disk
SATA3, SATA4 Slave Data disk
Page view 44
1 2 ... 40 41 42 43 44 45 46 47 48 49 50 ... 127 128

Comments to this Manuals

No comments