Asus P5MT-C Specifications Page 45
- Page / 154
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
ASUS P5MT-C 2-25
3. Serial ATA connectors (7-pin SATA1, SATA2, SATA3,
SATA4)
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
If you installed Serial ATA hard disk drives, you can create a RAID
0, RAID 1, RAID 0+1, and software RAID 5 configuration using the
Intel
®
Matrix Storage Technology or RAID 0, RAID 1 and RAID 0+1
configuration using the LSI MegaRAID
®
utility embedded on the Intel
®
ICH7R Southbridge.
Serial ATA hard disk drive connection
Connector Setting Use
SATA1/SATA2 Master Boot disk
SATA3/SATA4 Slave Data disk
These connectors are set Standard IDE mode by default. In Standard IDE
mode, you can connect Serial ATA boot/data hard disk drives to these
connectors. If you intend to create a Serial ATA RAID set using these
connectors, set the Configure SATA as item in the BIOS to [RAID]. See
section “4.3.5 IDE Configuration” for details.
Important notes on Serial ATA
• You must install Windows
®
2000 Service Pack 4 or Windows
®
2003
before using Serial ATA hard disk drives. The Serial ATA RAID
feature (RAID 0/RAID 1) is available only if you are using Windows
®
2000/2003.
• Use only two Serial ATA RAID connectors for each RAID 0 or RAID 1
set.
• When using the connectors in IDE mode, connect the primary (boot)
hard disk drive to the SATA1 or SATA2 connector. Refer to the table
below for the recommended SATA hard disk drive connections.
P5MT-C SATA Connectors
SATA2
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXN1
RSATA_RXP1
GND
SATA1
GND
RSATA_TXP0
RSATA_TXN0
GND
RSATA_RXN0
RSATA_RXP0
GND
SATA4
GND
RSATA_TXP3
RSATA_TXN3
GND
RSATA_RXN3
RSATA_RXP3
GND
SATA3
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXN2
RSATA_RXP2
GND
P5MT-C
2
®
- Motherboard 1
- Revised Edition V2 2
- March 2006 2
- Contents 3
- Safety information 8
- About this guide 9
- Typography 10
- P5MT-C specifications summary 11
- Product 13
- 1.1 Welcome! 15
- 1.2 Package contents 15
- 1.3 Special features 16
- Gigabit LAN solution 17
- Serial ATA II technology 17
- Built-in SATA RAID solution 17
- USB 2.0 technology 17
- CrashFree BIOS 2 18
- ASUS Smart Fan technology 18
- ASUS MyLogo2™ 18
- Hardware 19
- 2.1 Before you proceed 21
- 2.2 Motherboard overview 22
- 2.2.3 Motherboard layout 23
- 2.2.4 Layout contents 24
- ASUS P5MT-C 2-5 25
- 2.3.1 Installing the CPU 26
- Fastener 29
- Motherboard hole 29
- Narrow end 29
- ASUS P5MT-C 2-11 31
- Narrow end of the groove 32
- 2.4 System memory 33
- 112 Pins128 Pins 33
- 2.4.3 Installing a DIMM 34
- 2.4.4 Removing a DIMM 34
- 2.5 Expansion slots 35
- 2.5.3 Interrupt assignments 36
- 2.5.5 PCI slots 37
- 2.5.4 PCI Express x8 slots 37
- 2.6 Jumpers 38
- P5MT-C FM CPU Setting 39
- P5MT-C Keyboard Power Setting 40
- P5MT-C VGA Setting 40
- LSI RAID ROM 41
- (Default) 41
- INTEL RAID ROM 41
- P5MT-C BIOS Recovery Setting 42
- RECOVERY1 42
- 2.7 Connectors 43
- NOTE: Orient the red markings 44
- (usually zigzag) on the IDE 44
- Connector Setting Use 45
- P5MT-C USB 2.0 Connectors 46
- SYS-THEAMAL2 47
- I2C_DATA 48
- 24-pin Power Connector 49
- GND+12V DC 49
- P5MT-C System Panel Connector 50
- Powering up 51
- AMI BIOS beep codes 53
- 3-2 Chapter 3: Powering up 54
- BIOS setup 55
- DOS environment 57
- 2000 environment 57
- 4.1.2 AFUDOS utility 58
- Updating the BIOS file 59
- 4-4 Chapter 4: BIOS setup 60
- 4.1.4 ASUS Update utility 63
- 4-8 Chapter 4: BIOS setup 64
- 4.2 BIOS setup program 66
- 4.2.2 Menu bar 67
- 4.2.1 BIOS menu screen 67
- 4.2.3 Navigation keys 67
- 4-12 Chapter 4: BIOS setup 68
- 4.3 Main menu 69
- Type [Auto] 70
- LBA/Large Mode [Auto] 70
- 4.3.5 IDE Configuration 71
- IDE Detect Time Out [35] 72
- 4.3.6 System Information 73
- 4.4 Advanced menu 74
- MPS Configuration 75
- MPS Revision [1.4] 75
- Select MPS Revision 75
- Remote Access [Disabled] 76
- Select Remote Access 76
- 4.4.4 CPU Configuration 77
- 4.4.5 Chipset 78
- PEG Port [Enabled] 79
- Parallel Port Address [378] 80
- Parallel Port Mode [ECP] 80
- 4.4.7 PCI PnP 81
- 4.5 Power menu 82
- 4.5.2 APM Configuration 83
- 4.5.3 Hardware Monitor 84
- ASUS P5MT-C 4-29 85
- 4.6 Boot menu 86
- ASUS P5MT-C 4-31 87
- 4.6.3 Security 88
- Change User Password 89
- 4.7 Exit menu 90
- Exit & Discard Changes 91
- Discard Changes 91
- Load Setup Defaults 91
- Exit & Save Changes 91
- 4-36 Chapter 4: BIOS setup 92
- RAID support 93
- 5.1 RAID configurations 95
- BIOS Setup 96
- 5.2 Intel 97
- ROM Utility 97
- ASUS P5MT-C 5-5 99
- ASUS P5MT-C 5-7 101
- ASUS P5MT-C 5-9 103
- 5.2.5 Deleting a RAID set 104
- 5.2.7 Exiting the Intel 105
- Matrix Storage Manager 105
- utility 105
- 5.2.8 Rebuilding the RAID 106
- Utility 107
- 5.3.1 Creating a RAID set 109
- Using Easy Configuration 110
- ASUS P5MT-C 5-17 111
- ASUS P5MT-C 5-19 113
- Using New Configuration 114
- ASUS P5MT-C 5-21 115
- ASUS P5MT-C 5-23 117
- Using the Initialize command 118
- ASUS P5MT-C 5-25 119
- Using the Objects command 120
- ASUS P5MT-C 5-27 121
- Using the Rebuild command 123
- Using the Check Consistency 125
- ASUS P5MT-C 5-35 129
- 5.4 Global Array Manager 130
- Driver installation 131
- Chapter summary 132
- 6.1 RAID driver installation 133
- 2000/2003 Server 134
- 2000/2003 Server OS 135
- During Windows 135
- SATA RAID 136
- To an existing Windows 137
- ASUS P5MT-C 6-7 139
- Enterprise ver. 3.0 140
- ASUS P5MT-C 6-9 141
- 6.2 LAN driver installation 143
- 6.2.2 Red Hat 144
- 6.3 VGA driver installation 145
- utilities installation 147
- 6.4.4 Utilities menu 148
- 6.4.5 Contact information 148
- Reference information 149
- Appendix summary 150
- A.1 Intel 151
- A.2 Enhanced Intel SpeedStep 151
- Technology (EIST) 151
- A.2.2 Using the EIST 152
- A.3 Intel 153
- Hyper-Threading Technology 153
- A.4 Block diagrams 154
Comments to this Manuals
Related products and manuals for Server/workstation motherboards Asus P5MT-C
(64 pages)© 2020, manymanuals.com. All rights reserved. | 0.558 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Scale formation inhibitors are chemicals that are mixed into feed water supplied to the pipeline.