Asus Motherboard P5MT-S Specifications Page 101
- Page / 176
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
ASUS P5MT SeriesASUS P5MT Series
ASUS P5MT SeriesASUS P5MT Series
ASUS P5MT Series
5-15-1
5-15-1
5-1
5.1 Setting up RAID
The motherboard comes with the following RAID solutions:
P5MT modelP5MT model
P5MT modelP5MT model
P5MT model
•
LSI Logic Embedded SATA RAID LSI Logic Embedded SATA RAID
LSI Logic Embedded SATA RAID LSI Logic Embedded SATA RAID
LSI Logic Embedded SATA RAID technology embedded in the
Intel
®
ICH7R Southbridge supports up to two SATA hard disk drives and
RAID 0, RAID 1, and RAID 10 configurations.
P5MT/SCSI modelP5MT/SCSI model
P5MT/SCSI modelP5MT/SCSI model
P5MT/SCSI model
•
LSI Logic Embedded SATA RAIDLSI Logic Embedded SATA RAID
LSI Logic Embedded SATA RAIDLSI Logic Embedded SATA RAID
LSI Logic Embedded SATA RAID
•
LSI53C1020A PCI-X SCSI controller LSI53C1020A PCI-X SCSI controller
LSI53C1020A PCI-X SCSI controller LSI53C1020A PCI-X SCSI controller
LSI53C1020A PCI-X SCSI controller supports SCSI hard disk
drives and RAID 0, RAID 1, RAID 1-E configurations.
5.1.15.1.1
5.1.15.1.1
5.1.1
RAID definitionsRAID definitions
RAID definitionsRAID definitions
RAID definitions
RAID 0RAID 0
RAID 0RAID 0
RAID 0
(Data striping)
optimizes two identical hard disk drives to read and
write data in parallel, interleaved stacks. Two hard disks perform the same
work as a single drive but at a sustained data transfer rate, double that of
a single disk alone, thus improving data access and storage. Use of two
new identical hard disk drives is required for this setup.
RAID 1RAID 1
RAID 1RAID 1
RAID 1
(Data mirroring)
copies and maintains an identical image of data from
one drive to a second drive. If one drive fails, the disk array management
software directs all applications to the surviving drive as it contains a
complete copy of the data in the other drive. This RAID configuration provides
data protection and increases fault tolerance to the entire system. Use two
new drives or use an existing drive and a new drive for this setup. The new
drive must be of the same size or larger than the existing drive.
RAID 1RAID 1
RAID 1RAID 1
RAID 1
-E-E
-E-E
-E
(Enhanced RAID 1)
has a striped layout with each stripe unit
having a secondary (or alternate) copy stored on a different disk. You can
use three or more hard disk drives for this configuration.
RAID 0+1RAID 0+1
RAID 0+1RAID 0+1
RAID 0+1 is
data striping
and
data mirroring
combined without parity
(redundancy data) having to be calculated and written. With the RAID 0+1
configuration you get all the benefits of both RAID 0 and RAID 1
configurations. Use four new hard disk drives or use an existing drive and
three new drives for this setup.
JBODJBOD
JBODJBOD
JBOD
(Spanning)
stands for
Just a Bunch of DisksJust a Bunch of Disks
Just a Bunch of DisksJust a Bunch of Disks
Just a Bunch of Disks and refers to hard
disk drives that are not yet configured as a RAID set. This configuration
stores the same data redundantly on multiple disks that appear as a single
disk on the operating system. Spanning does not deliver any advantage
over using separate disks independently and does not provide fault
tolerance or other RAID performance benefits.
If you want to boot the system from a hard disk drive included in a
created RAID set, copy first the RAID driver from the support CD to a
floppy disk before you install an operating system to the selected hard
disk drive. Refer to Chapter 6 for details.
- Motherboard 1
- Contents 3
- Safety information 8
- About this guide 9
- P5MT/SCSI model) 11
- (P5MT/SCSI model only) 12
- 1.1 Welcome! 15
- 1.2 Package contents 15
- 1.3 Special features 16
- (P5MT/SCSI model only) 17
- Hardware 19
- 2.1 Before you proceed 21
- 2.2 Motherboard overview 22
- P5MT modelP5MT model 23
- P5MT model 23
- P5MT/SCSI model 24
- P5MT Series CPU Socket 775 27
- CPU_FAN2 31
- CPU_FAN1 31
- 2.4 System memory 33
- 2.5 Expansion slots 35
- 2.6 Jumpers 38
- P5MT Series FM CPU Setting 39
- P5MT Series VGA setting 40
- P5MT Series LAN_EN1 setting 41
- P5MT Series LAN_EN2 setting 41
- 2.7 Connectors 43
- P5MT Series IDE connector 44
- PRI_IDE1 44
- ADD_IN_CARD_ACT# 46
- P5MT Series TRPWR connector 48
- P5MT Series Fan connectors 49
- REAR_FAN2REAR_FAN1 49
- FRNT_FAN1 FRNT_FAN2 49
- CPU_FAN2CPU_FAN1 49
- 24-pin Power Connector 50
- Powering up 53
- AMI BIOS beep codes 55
- 3.2 Powering off the computer 56
- BIOS setup 57
- DOS environment 59
- XP environment 59
- Copying the current BIOS 60
- Updating the BIOS file 61
- Installing ASUS Update 65
- 4.2 BIOS setup program 68
- System Time [11:10:19] 70
- System Date [Thu 06/17/2005] 70
- IDE Configuration 70
- System Information 70
- 4.3 Main menu 71
- Configure SATA As [IDE] 72
- 4.4 Advanced menu 76
- NorthBridge Configuration 81
- PEG Port [Auto] 82
- PCI Express Port 0 [Auto] 83
- PCI Express Port 4 [Auto] 83
- PCI Express Port 5 [Auto] 83
- Serial Port2 Mode [Normal] 84
- Parallel Port IRQ [IRQ7] 84
- 4.5 Power menu 86
- RTC Alarm Date (Days) 88
- System Time 88
- 4.6 Boot menu 91
- Change Supervisor Password 93
- 4.7 Exit menu 96
- Load Setup Defaults 97
- Chapter summary 100
- 5.1 Setting up RAID 101
- Setup Utility 104
- Using Easy Configuration 105
- Using New Configuration 110
- Using the Initialize command 118
- Using the Objects command 120
- Using the Check Consistency 125
- 5.3 Global Array Manager 130
- Device Properties 139
- RAID Properties 141
- Deleting arrays 147
- 6.1 RAID driver installation 153
- SuSE LinuxSuSE Linux 161
- SuSE Linux 161
- 6.2 LAN driver installation 163
- 6.3 VGA driver installation 165
- Reference information 169
- Appendix summary 170
- A.1 Intel 171
- A.2 Enhanced Intel SpeedStep 171
- Technology (EIST) 171
- A.3 Intel 173
- Hyper-Threading Technology 173
- A.4 Block diagrams 174
- PCI-E interfaces 175
Related products and manuals for Server/workstation motherboards Asus Motherboard P5MT-S
(112 pages)© 2020, manymanuals.com. All rights reserved. | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals