Asus AAM6000EV Specifications Page 31
- Page / 69
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Description:
This command deletes a device from the bridge configuration. The changes will only take place after the configuration is
saved and the system is rebooted. The syntax of the device name is the same as that for the
device add
command.
Configuration saving saves this information.
Example:
DSL bridge> device delete edd
13.4.3. device list
Syntax:
device list
Description:
This command lists all the devices that are currently attached to the bridge. It does not show the stored configuration
(which can be seen with the
config print
command).
Example:
DSL bridge> device list
13.4.4. ethertype
Syntax:
ethertype [<port> any|ip|pppoe]
Description:
This command enables filtering of Ethernet packets according to the
ETHER_TYPE
field in the header. Only packets of
the type specified using this command will be sent on the port specified; packets of all types will always be received. By
default, all bridge ports are set to “any”, which means that the type of the packet will never be checked. The meaning of
the other options is as follows:
Option Permitted ETHER_TYPE values
“ip” 0x0800
– IP
0x0806
– ARP
“pppoe” 0x8863, 0x8864
– PPP Over Ethernet (RFC 2516)
The port is specified as an integer, as displayed by the
device list
command. When using this command in the
initbridge
configuration file, ports are numbered in the order in which the
device add
commands are given, starting
from 1.
If no arguments are given, the current settings for each port are displayed.
Example:
DSL bridge> ethertype 2 any
13.4.5. filter
Syntax:
filter
Description:
This command shows the current contents of the bridge’s filter table. The MAC entries for each device are shown in turn
together with the time that the MAC address was last seen by the bridge. The command also shows the current filter
ageing time, in seconds, and the number of creation failures since the system was started. Creation failures occur when
there is no room left in the filter table for a new entry.
Example:
DSL bridge> filter
- 31 -
- Solwise 1
- Setup instructions for 3
- Solwise SAR703 ADSL Router 3
- 1. Introduction 7
- 2. Getting Started 8
- 2.2. Configuration Software 9
- 4. Client TCP Setup 12
- 5. Testing 14
- 6. Port Forwading 15
- 7. Advanced PPP Settings 16
- 8. Firmware Upgrade 17
- Stop Bits :1 18
- Flow Control :None 18
- BPS :9600 18
- Data bits :8 18
- Parity :None 18
- 10. CLI Configuration 20
- Ethernet 21
- > ip nat add ppp_device ↵ 22
- 11.3. SNMP 25
- 13.2.2. help 28
- 13.2.3. (history mechanism) 28
- 13.3.4. isfs rm 30
- 13.3.5. flashfs update 30
- 13.4.1. device add 30
- 13.4.2. device delete 30
- 13.4.3. device list 31
- 13.4.4. ethertype 31
- 13.4.5. filter 31
- 13.4.6. filterage 32
- 13.4.7. flush 32
- 13.4.8. portfilter 32
- 13.4.9. status 32
- 13.4.12. spanning hellotime 33
- 13.4.13. spanning maxage 34
- 13.4.18. spanning priority 35
- 13.4.19. spanning status 35
- 13.5.1. arp 36
- 13.5.2. config 36
- 13.5.3. device 37
- 13.5.4. disable 39
- 13.5.5. enable 39
- 13.5.6. get 40
- 13.5.7. ipatm abort 40
- 13.5.8. ipatm arp 40
- 13.5.9. ipatm arpserver 40
- 13.5.10. ipatm files 41
- 13.5.11. ipatm lifetime 41
- 13.5.12. ipatm pvc 41
- 13.5.13. iphostname 42
- 13.5.14. norelay 42
- 13.5.15. ping 43
- 13.5.16. portname 43
- 13.5.17. relay 44
- 13.5.18. rip accept 45
- 13.5.19. rip allowed 45
- 13.5.20. rip boot 45
- 13.5.21. rip hostroutes 46
- 13.5.22. rip killrelay 46
- 13.5.23. rip poison 46
- 13.5.24. rip relay 46
- 13.5.25. rip relays 47
- 13.5.26. rip send 47
- 13.5.27. route 47
- 13.5.28. routeflush 48
- 13.5.29. routes 49
- 13.5.30. stats 49
- 13.5.31. subnet 49
- 13.6.1. ip nat 50
- 13.6.2. nat interfaces 50
- 13.6.3. nat inbound 50
- 13.6.4. nat info 51
- 13.6.5. nat protocol 52
- 13.6.6. nat sessions 52
- 13.6.7. nat stats 52
- Channels 53
- Interfaces 53
- Interface 1 and Channel 1 53
- 13.7.14. <channel> llc 56
- 13.7.15. <channel> pvc 56
- 13.7.16. <channel> qos 56
- 13.7.18. <channel> svc 57
- 13.7.21. bcp 58
- 13.7.24. user 59
- 13.8.1. access 59
- 13.8.2. config 60
- 13.8.3. trap 60
- 13.9.1. show rate 60
- 13.9.2. show defect 60
- 13.9.10. up 62
- 13.9.11. show id 62
- 15.1. Power Adapter 63
- 17. Appendix C Glossary 65
- European CTR 21 compliance 69
Related products and manuals for Networking Asus AAM6000EV
Networking Asus AAM6010EV-T4 User Manual
(38 pages)
(38 pages)
Networking Asus M2NBP-VM-CSM User Manual
(38 pages)
(38 pages)
Networking Asus eMTA Technical Information
(53 pages)
(53 pages)
Networking Asus RT-N10E User Manual
(46 pages)
(46 pages)
Networking Asus AAM6000EV Manual
(17 pages)
(17 pages)
Networking Asus P4B User Manual
(122 pages)
(122 pages)
Networking Asus RT-AC68R User Manual
(70 pages)
(70 pages)
Networking Asus P4B User Manual
(32 pages)
(32 pages)
(92 pages)
Networking Asus GIGAX2048 User Manual
(115 pages)
(115 pages)
Networking Asus RT-N15U User Manual
(60 pages)
(60 pages)
Networking Asus RT-N12 User Manual
(53 pages)
(53 pages)
(120 pages)
Networking Asus WL-100G User Manual
(91 pages)
(91 pages)
Networking Asus WL-100G User Manual
(57 pages)
(57 pages)
Toastmaster Miksery podręczniki użytkownika
Lista Toastmaster Miksery produkty zawierają 19 instrukcje obsługi do modeli 19. Wszystkie podręczniki użytkownika w formacie pdf są dostępne do pobrania lub obejrzenia online.
© 2020, manymanuals.com. All rights reserved. | 0.029 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals