Asus AAM6000EV Specifications Page 34
- Page / 69
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
DSL bridge> spanning hellotime 5 ;
Sets the hello time
to 5 seconds
13.4.13. spanning maxage
Syntax:
spanning maxage [<time>]
Description:
Reads or sets the maximum age of received spanning tree protocol information before it is discarded, and is used when
the bridge is or is attempting to become the root bridge. The maxage time may be any value between 6 and 40 and is also
constrained by the forwarddelay and hellotime times. The maxage time may also be changed by SNMP command.
Configuration saving saves this information. By default the maxage time is set to 20 seconds.
Example:
DSL bridge> spanning maxage 6 ;
Sets the maxage
time to 6 seconds
13.4.14. spanning port <number>
The port commands, described in subsequent sections, control the configuration of the bridge’s ports so far as the
operation of the spanning tree protocol is concerned. Ports are numbered from 1. Every port on the bridge may be
specified by typing
all
instead of a port number.
13.4.15. spanning port <number> disabled | enable
Syntax:
spanning port <number> disable | enable
Description:
Allows a port to be disabled or enabled. The state of a port may also be changed by SNMP command. A port, which is
enabled will take part in the operation of the spanning tree protocol. If enabled, the physical port may be “enabled” or
“disabled” as demanded by the operation of the protocol.
Configuration saving saves this information. By default ports are enabled.
Example:
DSL bridge> spanning port 1 enable ;
Enables port 1 on
the bridge.
13.4.16. spanning port <number> pathcost
Syntax:
spanning port <number> pathcost [<cost>]
Description:
Reads or sets the cost of using this port. The cost may be any number between 1 and 65535. The cost of the port is used
when deciding which is the best path to the root bridge. The cost of a port may also be changed by SNMP command.
Configuration saving saves this information. By default a cost of 10 is assigned to a port
Example:
DSL bridge> spanning port 2 pathcost ;
Displays the path
cost for port 2 on the bridge
- 34 -
- Solwise 1
- Setup instructions for 3
- Solwise SAR703 ADSL Router 3
- 1. Introduction 7
- 2. Getting Started 8
- 2.2. Configuration Software 9
- 4. Client TCP Setup 12
- 5. Testing 14
- 6. Port Forwading 15
- 7. Advanced PPP Settings 16
- 8. Firmware Upgrade 17
- Stop Bits :1 18
- Flow Control :None 18
- BPS :9600 18
- Data bits :8 18
- Parity :None 18
- 10. CLI Configuration 20
- Ethernet 21
- > ip nat add ppp_device ↵ 22
- 11.3. SNMP 25
- 13.2.2. help 28
- 13.2.3. (history mechanism) 28
- 13.3.4. isfs rm 30
- 13.3.5. flashfs update 30
- 13.4.1. device add 30
- 13.4.2. device delete 30
- 13.4.3. device list 31
- 13.4.4. ethertype 31
- 13.4.5. filter 31
- 13.4.6. filterage 32
- 13.4.7. flush 32
- 13.4.8. portfilter 32
- 13.4.9. status 32
- 13.4.12. spanning hellotime 33
- 13.4.13. spanning maxage 34
- 13.4.18. spanning priority 35
- 13.4.19. spanning status 35
- 13.5.1. arp 36
- 13.5.2. config 36
- 13.5.3. device 37
- 13.5.4. disable 39
- 13.5.5. enable 39
- 13.5.6. get 40
- 13.5.7. ipatm abort 40
- 13.5.8. ipatm arp 40
- 13.5.9. ipatm arpserver 40
- 13.5.10. ipatm files 41
- 13.5.11. ipatm lifetime 41
- 13.5.12. ipatm pvc 41
- 13.5.13. iphostname 42
- 13.5.14. norelay 42
- 13.5.15. ping 43
- 13.5.16. portname 43
- 13.5.17. relay 44
- 13.5.18. rip accept 45
- 13.5.19. rip allowed 45
- 13.5.20. rip boot 45
- 13.5.21. rip hostroutes 46
- 13.5.22. rip killrelay 46
- 13.5.23. rip poison 46
- 13.5.24. rip relay 46
- 13.5.25. rip relays 47
- 13.5.26. rip send 47
- 13.5.27. route 47
- 13.5.28. routeflush 48
- 13.5.29. routes 49
- 13.5.30. stats 49
- 13.5.31. subnet 49
- 13.6.1. ip nat 50
- 13.6.2. nat interfaces 50
- 13.6.3. nat inbound 50
- 13.6.4. nat info 51
- 13.6.5. nat protocol 52
- 13.6.6. nat sessions 52
- 13.6.7. nat stats 52
- Channels 53
- Interfaces 53
- Interface 1 and Channel 1 53
- 13.7.14. <channel> llc 56
- 13.7.15. <channel> pvc 56
- 13.7.16. <channel> qos 56
- 13.7.18. <channel> svc 57
- 13.7.21. bcp 58
- 13.7.24. user 59
- 13.8.1. access 59
- 13.8.2. config 60
- 13.8.3. trap 60
- 13.9.1. show rate 60
- 13.9.2. show defect 60
- 13.9.10. up 62
- 13.9.11. show id 62
- 15.1. Power Adapter 63
- 17. Appendix C Glossary 65
- European CTR 21 compliance 69
Related products and manuals for Networking Asus AAM6000EV
Networking Asus AAM6010EV-T4 User Manual
(38 pages)
(38 pages)
Networking Asus M2NBP-VM-CSM User Manual
(38 pages)
(38 pages)
Networking Asus eMTA Technical Information
(53 pages)
(53 pages)
Networking Asus RT-N10E User Manual
(46 pages)
(46 pages)
Networking Asus AAM6000EV Manual
(17 pages)
(17 pages)
Networking Asus P4B User Manual
(122 pages)
(122 pages)
Networking Asus RT-AC68R User Manual
(70 pages)
(70 pages)
Networking Asus P4B User Manual
(32 pages)
(32 pages)
(92 pages)
Networking Asus GIGAX2048 User Manual
(115 pages)
(115 pages)
Networking Asus RT-N15U User Manual
(60 pages)
(60 pages)
Networking Asus RT-N12 User Manual
(53 pages)
(53 pages)
(120 pages)
Networking Asus WL-100G User Manual
(91 pages)
(91 pages)
Networking Asus WL-100G User Manual
(57 pages)
(57 pages)
© 2020, manymanuals.com. All rights reserved. | 0.294 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals