Asus AAM6000EV Specifications Page 46
- Page / 69
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Broadcasts a request for RIP information from other machines. TCP/IP does this automatically when it first starts up, and
the routing information should be kept up to date by regular broadcasts from the other machines, so this command is
normally of little use.
Example:
DSL> ip rip boot
13.5.21. rip hostroutes
Syntax:
rip hostroutes [off]
Description:
Sets or clears the “hostroutes” flag; TCP/IP will accept RIP routes to individual hosts only if this flag is on. If the
flag is off, then RIP version 1 routes that appear to be to individual hosts will be treated as if they were to the network
containing the host; RIP version 2 routes to individual hosts will be ignored. (The reason for this difference is that RIP
version 1 does not allow specification of subnet masks; a RIP version 1 route that appears to be to an individual host
might in fact be to a subnet, and treating it as a route to the whole network may be the best way to make use of the
information.) To see the state of the flag without changing it, the “config” command must be used.
Configuration saving saves this information. By default the “hostroutes” flag is off.
Example:
DSL> ip rip hostroutes off
13.5.22. rip killrelay
Syntax:
rip killrelay <relay>
Description:
Deletes a RIP relay. See “rip relay” for information on RIP relays.
13.5.23. rip poison
Syntax:
rip poison [off]
Description:
Sets or clears the “poisoned reverse” flag. If this flag is on, TCP/IP performs “poisoned reverse” as defined
in RFC 1058; see that RFC for discussion of when this is a good thing. To see the state of the flag without changing it,
the “config” command must be used.
Configuration saving saves this information. By default the “poisoned reverse” flag is off.
Example:
DSL> ip rip poison
13.5.24. rip relay
Syntax:
rip relay <RIP version> <name> [<i/f> [<timeout>]]
Description:
Configures a RIP relay. RIP relays were designed as a means of using RIP on a non-broadcast medium (currently, only
IP-over-ATM); on such an interface, TCP/IP will send RIP information individually to each configured RIP relay, instead
- 46 -
- Solwise 1
- Setup instructions for 3
- Solwise SAR703 ADSL Router 3
- 1. Introduction 7
- 2. Getting Started 8
- 2.2. Configuration Software 9
- 4. Client TCP Setup 12
- 5. Testing 14
- 6. Port Forwading 15
- 7. Advanced PPP Settings 16
- 8. Firmware Upgrade 17
- Stop Bits :1 18
- Flow Control :None 18
- BPS :9600 18
- Data bits :8 18
- Parity :None 18
- 10. CLI Configuration 20
- Ethernet 21
- > ip nat add ppp_device ↵ 22
- 11.3. SNMP 25
- 13.2.2. help 28
- 13.2.3. (history mechanism) 28
- 13.3.4. isfs rm 30
- 13.3.5. flashfs update 30
- 13.4.1. device add 30
- 13.4.2. device delete 30
- 13.4.3. device list 31
- 13.4.4. ethertype 31
- 13.4.5. filter 31
- 13.4.6. filterage 32
- 13.4.7. flush 32
- 13.4.8. portfilter 32
- 13.4.9. status 32
- 13.4.12. spanning hellotime 33
- 13.4.13. spanning maxage 34
- 13.4.18. spanning priority 35
- 13.4.19. spanning status 35
- 13.5.1. arp 36
- 13.5.2. config 36
- 13.5.3. device 37
- 13.5.4. disable 39
- 13.5.5. enable 39
- 13.5.6. get 40
- 13.5.7. ipatm abort 40
- 13.5.8. ipatm arp 40
- 13.5.9. ipatm arpserver 40
- 13.5.10. ipatm files 41
- 13.5.11. ipatm lifetime 41
- 13.5.12. ipatm pvc 41
- 13.5.13. iphostname 42
- 13.5.14. norelay 42
- 13.5.15. ping 43
- 13.5.16. portname 43
- 13.5.17. relay 44
- 13.5.18. rip accept 45
- 13.5.19. rip allowed 45
- 13.5.20. rip boot 45
- 13.5.21. rip hostroutes 46
- 13.5.22. rip killrelay 46
- 13.5.23. rip poison 46
- 13.5.24. rip relay 46
- 13.5.25. rip relays 47
- 13.5.26. rip send 47
- 13.5.27. route 47
- 13.5.28. routeflush 48
- 13.5.29. routes 49
- 13.5.30. stats 49
- 13.5.31. subnet 49
- 13.6.1. ip nat 50
- 13.6.2. nat interfaces 50
- 13.6.3. nat inbound 50
- 13.6.4. nat info 51
- 13.6.5. nat protocol 52
- 13.6.6. nat sessions 52
- 13.6.7. nat stats 52
- Channels 53
- Interfaces 53
- Interface 1 and Channel 1 53
- 13.7.14. <channel> llc 56
- 13.7.15. <channel> pvc 56
- 13.7.16. <channel> qos 56
- 13.7.18. <channel> svc 57
- 13.7.21. bcp 58
- 13.7.24. user 59
- 13.8.1. access 59
- 13.8.2. config 60
- 13.8.3. trap 60
- 13.9.1. show rate 60
- 13.9.2. show defect 60
- 13.9.10. up 62
- 13.9.11. show id 62
- 15.1. Power Adapter 63
- 17. Appendix C Glossary 65
- European CTR 21 compliance 69
Related products and manuals for Networking Asus AAM6000EV
Networking Asus AAM6010EV-T4 User Manual
(38 pages)
(38 pages)
Networking Asus M2NBP-VM-CSM User Manual
(38 pages)
(38 pages)
Networking Asus eMTA Technical Information
(53 pages)
(53 pages)
Networking Asus RT-N10E User Manual
(46 pages)
(46 pages)
Networking Asus AAM6000EV Manual
(17 pages)
(17 pages)
Networking Asus P4B User Manual
(122 pages)
(122 pages)
Networking Asus RT-AC68R User Manual
(70 pages)
(70 pages)
Networking Asus P4B User Manual
(32 pages)
(32 pages)
(92 pages)
Networking Asus GIGAX2048 User Manual
(115 pages)
(115 pages)
Networking Asus RT-N15U User Manual
(60 pages)
(60 pages)
Networking Asus RT-N12 User Manual
(53 pages)
(53 pages)
(120 pages)
Networking Asus WL-100G User Manual
(91 pages)
(91 pages)
Networking Asus WL-100G User Manual
(57 pages)
(57 pages)
© 2020, manymanuals.com. All rights reserved. | 0.117 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals